News

Artificial Grass To Achieve The Best Bonding Effect



1, before the approach construction, the foundation of the flatness, slope and surface perception to be detected, the need for dressing the dressing measures and requirements,Artificial Grass to meet the requirements before they can approach construction.

The following are the same as the "

2, the line (measurement), to find the center of the site and two semi-circular center, and according to the three positioning point of the grading line, set the center line and edge intersection, and then the finale of the corner , The exact location of the line, and then set the function points,Artificial Grass the location of the line, and ink lines or paint line pop.

The following are the same as the "

3, the turf moved into the field along the horizontal direction of the spread, and in turn from one end of the longitudinal side to the other end of the advance, spread out,Artificial Grass try to make the grass in the grass on the white line in the functional line position, reducing the number of cutting.

The following are the same as the "

4, will be woven in the turf outside and failed to place the line to the function of the white line cut off, placed aside,Artificial Grass if the white line is another weaving, you must manually cut into the site corresponding function line width white Crossed the line.

The following are the same as the "

5, the green turf joints at the lap 1cm, with a curling knife from the lap in the central cut, so that both sides of the turf as close as possible compact, and then cut the knife to cut. 6, the seams at the bottom of the bottom of the turf up, each side of the turf width of about 50 cm, and then 25 cm wide strip along the turf seams center out, the special glue were painted in the turf Sewn at the bottom and the connection belt,Artificial Grass turf seam coating brush with brush, brush plastic width of 6 cm. The strap is evenly coated with a squeegee on the connecting belt. In order to achieve the best bonding effect, use the glue before the full mixing or reverse the packaging barrel several times, so that even mixing glue. Brushing in the same direction when the glue, which will drive out the air and improve the uniformity of the coating, enhance the adhesive force. Drying: glue and other natural evaporation of the glue,Artificial Grass after the glue must be dry for some time, until the solvent volatile clean, so that the adhesive layer sticky or produce bubbles, affecting the quality of bonding. Dry time should not be too long, so as not to lose glue sticky, resulting in degumming. To be adhesive layer was dry film (about 5-25 minutes) / 25 ℃ can be bonded. Adhesive: Bonding on both sides of the turf should be a one-time alignment of the adhesive tape (if the stitching found before the gap at the greater gap, from the gap at 2-5cm horizontal position, along the longitudinal direction of the gap cut,Artificial Grass Interface to stretch to ensure that the appearance of beautiful), and the need to press the real, so that the bonding part of the close, do not move back and forth, so as not to affect the bonding effect. If the turf or connection with a wet phenomenon, you need to dry half an angel dry.

7, after the basic stitching in the turf,Artificial Grass once again set the line of the functional line, the exact location of the point to cut the knife cut out, cut out the cut grass, the connection belt into, scraping glue, the original ready Of the white grass line back, after bonding, with rubber hammer repeatedly beat, so that part of the connection close.

The following are the same as the "

8, when the turf paved finish, the turf on the part of the fold need to cut the knife, straighten the dock, remove the overlapping part, and then cemented.

The following are the same as the "

9, all the grass after bonding, with a brush machine to sort out. The first pass with the brush machine will be the audience of the lodging of the grass line up.

The following are the same as the "

10, according to the specifications of 4m * 4m put the audience, according to different grass height per square meter of sand injection kilograms of quartz sand evenly spread to the specified area,Artificial Grass with a brush machine to disperse the quartz sand and The grass lines are combed and combed once.

The following are the same as the "

11, according to the specifications of 4m * 4m put the audience,Artificial Grass according to different grass height per square meter of the number of particles per gram of plastic particles spread evenly to the specified area, with the brush machine will spread evenly The grass line comb, and vertical and horizontal combing once.

12, fill all completed, and then brush the grass vertical and horizontal combing the grass fiber once.

13, after the completion of the work, in accordance with the quality requirements of artificial grass surface testing and clearance, the rectification of the rectification.

14, the completion of acceptance.